Set up PC or Laptop

Installation on PC’s using Win2000 OS. Please take all the defaults during installation.

 

  1. Log as Administrator
  2. Install Keaterm from the CD.  (\KeaTerm\SETUP.EXE)

 

 

  1. Open a Command Prompt window and change the path to the CD drive letter. Run the Collado.bat file as shown.

 

 

 

  1. Update IE to 5.5 from the CD. (\IE55\ie5setup.exe)

 

 

 

  1. Install Winzip80 from the CD.

 

 

 

  1. Install Active Perl from the CD (\ActivePerl\ActivePerl-5.6.0.616-MSWin32-x86-multi-thread.msi)

 

 

 

 

  1. Logout and then login again to activate Active Perl.

 

 

 

  1. Select Start, Run, and type the following command: ppm install c:\tk\TK.ppd

 

 

  1. Open a Command Prompt window and change the path to the CD drive letter. Run the FileDialog.bat file as shown.

 

 

 

 

  1. Enable Telnet through Start, Settings, Control Panel, Administrative Tools, Telnet Server Administration

 

 

 

 

 

The Telnet Server Administration session starts - select 3 and press enter, select 7 and press enter, Change current value of 2 to 1 and then exit according to the instructions.

 

 

 

  1. Share c:\tools as tools.

 

 

 

  1. Share c:\var as var

 

 

 

 

  1. Right click on the My Computer Icon and select Properties.  Select the Advanced Tab and select Environment Variables. Edit the system variables path and add the following:           ;c:\tools;c:\var;c:\bin;c:\bin\Emacs

 

 

 

 

 

  1. Install Carbon Copy from the CD (\CC55Eng.exe). Instructions are on the CD (Marvel_CC32_readme.doc)

 

 

 

 

  1. From the CD run the Win2000_Plain_Password.reg file. (Double click on it)\

Reboot the system.

 

 

 

 

  1. Select Start, Settings, Network and Dial-Up Connections. Open Local Area Connections 2 and select Properties. Select Internet Protocol. Select Properties. Type the following information according to the following;

 

 

 

 

  1. Connect the LAN cable between the PC and the System Hub and ping the following address from the Command Prompt window;      ping 10.254.1.0

 

 

Note: If the above ping test fails, then find the PBM IP address based on the following rules. (The above IP is based on the following settings;

PBM 10.254.1.0 = PBM cabinet ID 0, drawer ID = 1)

 

The thirty two bit private LAN address is defined as follows:

 

nnnnnnnn. mmmmmmmm . pppppppp . eeeeeeee

 

The value of mmmmmmmm determines the meaning of the values of pppppppp and eeeeeeee.

 

LAN Address

The LAN address = nnnnnnnn = 10

Cabinet ID

Cabinet IDs are unique and are determined by the setting of the OCP push-wheel on each cabinet door.  Each cabinet must have a unique number.  Cabinet IDs are represented in network addresses in two ways depending upon whether you are addressing components in system space or components in IO space:

 

  1. When addressing system space components like MBMs, CMMs, and CPUs,  the upper 4 bits of mmmmmmmm are the cabinet ID number.

  2. When addressing IO space components like the PBM, mmmmmmmm = 254 and eeeeeeee = the cabinet ID.

 

The valid range for the cabinet ID set by the push-wheel on the cabinet door is 0 to 7.

MBM ID

The MBM ID is set by the push-wheel on the 2P or 8P drawer.    This ID corresponds to the address of the backplane in the drawer and is fundamental in determining other physical addresses for both the system and the server management LAN.  The lower four bits of mmmmmmmm are the MBM ID number.  Thus mmmmmmmm = a specific MBM in a specific cabinet.  With this unique number, firmware determines addresses for memory, CPUs, and the port locations for north, south, east, and west IP ports.

 

The valid range for the MBM ID set by the push-wheel on both the 2P and 8P drawers are 0 to 3.

PBM ID

The PBM ID is set by the push-wheel on the IO drawer.  When mmmmmmmm = 254, pppppppp = the PMB ID set by the push-wheel on the OCP of the IO drawer.

 

Network ID Table

 

 

If mmmmmmmm = Cabinet ID + MBM push- wheel

If mmmmmmmm = PBM flag (254 decimal)

If mmmmmmmm = special (253 decimal)

nnnnnnnn

network number (10 decimal)

network number (10 decimal)

network number (10 decimal)

mmmmmmmm

MBM in cab0,   1-4

MBM in cab1, 11-14

254

See special addresses

pppppppp

0 for MBM,
1-4 for CMM

PBM push-wheel

See special addresses

eeeeeeee

0 for CMM itself,
1-2 for EV7 ID,
when MBM specified, default  = 1

Cabinet ID push-wheel

See special addresses

 

Some examples

Device

 

Comment

MBM

10.1.0.1

MBM cabinet ID 0,  drawer ID  1 (eeeeeeee default = 1)

PBM

10.254.1.0

PBM cabinet ID 0, drawer ID  1

CMM

10.2.1.0

CMM #1 connected to MBM  2

EV7

10.2.1.2

second EV7 connected to CMM 1 connected MBM  2

 

Special Addresses

 

Address

Comment

PMU server

10.253.0.1

Address used to get to the PMU

Route for NXMs

10.253.0.2

default address for addresses not in the proper range of addresses

Telnet server

10.253.0.3

Dedicated address for a telnet  session

DHCP addresses  

10.253.0.4-253

DHCP address pool

Dedicated  PMU address

10.253.0.254

For VMS use

 

 

 

  1. Map a network drive as shown. 

Drive: W

Folder: \\rwhid1.mro.cpqcorp.net\marvelab

             

 

 

Username: marvel

Password: MarvelLab1+

 

 

 

  1.  Open a Command Prompt window and change the path to the CD drive letter. Run the TFTP.bat file as shown.

 

 

 

 

  1. An icon with the following name will be displayed on the desktop “tftpd32.exe”.  Run the tftpd32.exe program.

 
  1. Configure the TFTP Server as shown. 

Server interface: 10.253.0.254

 

 

 

 

Use the Browse button and select the following path for the Base Directory.

Base Directory: W:\fw_rel\

 

 

 

 

  1. The CD also contains Office 2000 patches, Acrobat Reader 5.0, IE 5.5 patches/security updates, TDS 6x V2.4 program, VISA 2.6 updates, and Omnix applications if needed.